设为首页 设为收藏

联系方式

 

洛阳松导感应加热科技有限公司 

联系方式:15038554363  

24小时技术热线:15038554363

邮 箱:1390003299@qq.com

厂址:河南省洛阳市洛新工业园区

  • 产品
  • 梯形铝锭在线提温设备

    0.2T中频定点浇注炉

    钢坯加热炉

    超高温烧结炉

    钢管在线加热及保温装置

    40KW感应加热取暖炉

    氮化硼专用中频加热线圈

    电机端环焊接设备

    电机转子导条焊机设备

    5吨中频炉熔化铸铁

    底出水熔铝炉

    侧下出水中频炉

    0.2吨铜雾化定点浇注炉

    3吨中频炉熔化铸钢件

    3吨中频炉熔化废铝

    3吨中频炉2500kw熔化铸铁

    1吨中频炉熔化铸铁件专用炉

    1吨12脉一拖二中频炉

    2吨中频炉用熔化铸钢件

    铸铁件1吨中频炉

    2吨铸造中频炉

    铸造1吨中频炉

    1.5吨钢壳液压中频炉

    1.5吨钢壳液压定点浇注炉

    3吨串联逆变中频炉

    圆钢感应加热炉

    铝棒感应加热炉

    方钢感应加热炉

    电炉行业动态新闻
    分享到:
        本文为技术资料或者文章来自网络,仅供参考学习,如涉嫌侵权,请告知删除
        

    缓存调制波熔铝炉安装流程

    电炉的安装工作必须按下列程序进行:

    1.安装前先熟悉说明书内容,并检查所有部件是否完备。

    2.根据地基图筑造地基,并将电炉安装在地基上。

    3.将坩埚装入炉内,注意坩埚口与导流罩之间不能留有缝隙,以防铝液溅入炉膛。

    4.按照电热元件接线图,把控制柜引出的电源线接好并确认电热元件连接与图样相符。

    5.接地装置螺栓上应接上可靠的接地线(包括电路配用控制柜),以保证操作人员安全。

    6.把测炉膛温度的热电偶穿过热电偶座插入炉膛,把用于测量铝液温度的热电偶根据安装角度固定好。热电偶与温控仪用补偿导线连接。

    7.炉体安装完毕后,应校正电炉工作台面水平度。

    8.检查高频电源线、控制柜、热电偶与补偿导线等导线接线端接触是否良好,并注意带电部分不应有裸露及短路现象。

    9.检查高频电源线是否有折断、裂纹、严重弯曲等现象。

    Buffer modulation wave aluminum melting furnace installation process

    The installation of the electric furnace must be carried out according to the following procedures:

    1. Familiarize yourself with the contents of the manual before installation, and check whether all components are complete.

    2. Build the foundation according to the foundation plan, and install the electric furnace on the foundation.

    3. Put the crucible into the furnace, pay attention to no gap between the crucible mouth and the deflector, to prevent the aluminum liquid from splashing into the furnace.

    4. According to the electric heating element wiring diagram, connect the power cord from the control cabinet and confirm that the electric heating element connection matches the drawing.

    5. A reliable grounding wire (including the control cabinet for circuit configuration) should be connected to the grounding device bolt to ensure the safety of the operator.

    6. Insert the thermocouple for measuring the temperature of the furnace into the furnace through the thermocouple holder, and fix the thermocouple for measuring the temperature of the molten aluminum according to the installation angle. The thermocouple and the temperature controller are connected with compensation wires.

    7. After the furnace body is installed, the levelness of the electric furnace work surface should be corrected.

    8. Check whether the terminals of high-frequency power cables, control cabinets, thermocouples and compensation wires are in good contact, and pay attention to the fact that the live parts should not be exposed or short-circuited.

    9. Check whether the high-frequency power cord is broken, cracked, severely bent, etc.

    https://songdaokeji.cn/category/products/induction-melting-furnace

    https://songdaokeji.cn/category/blog/induction-melting-furnace-related-information

    firstfurnace@gmil.com

    Telephone8618037961302


    Copyright© 2007-2013洛阳松导感应加热科技有限公司 All Rights Reserved 
    手 机:15038554363
    本站关键词:中频炉、中频电炉、熔炼炉