设为首页 设为收藏

联系方式

 

洛阳松导感应加热科技有限公司 

联系方式:15038554363  

24小时技术热线:15038554363

邮 箱:1390003299@qq.com

厂址:河南省洛阳市洛新工业园区

  • 产品
  • 梯形铝锭在线提温设备

    0.2T中频定点浇注炉

    钢坯加热炉

    超高温烧结炉

    钢管在线加热及保温装置

    40KW感应加热取暖炉

    氮化硼专用中频加热线圈

    电机端环焊接设备

    电机转子导条焊机设备

    5吨中频炉熔化铸铁

    底出水熔铝炉

    侧下出水中频炉

    0.2吨铜雾化定点浇注炉

    3吨中频炉熔化铸钢件

    3吨中频炉熔化废铝

    3吨中频炉2500kw熔化铸铁

    1吨中频炉熔化铸铁件专用炉

    1吨12脉一拖二中频炉

    2吨中频炉用熔化铸钢件

    铸铁件1吨中频炉

    2吨铸造中频炉

    铸造1吨中频炉

    1.5吨钢壳液压中频炉

    1.5吨钢壳液压定点浇注炉

    3吨串联逆变中频炉

    圆钢感应加热炉

    铝棒感应加热炉

    方钢感应加热炉

    电炉文章
    分享到:
        本文为技术资料或者文章来自网络,仅供参考学习,如涉嫌侵权,请告知删除
        

    一、概况:

    1、设备类型:

         本设备为节电型产品,采用半桥串联逆变中频电源(电压谐振)。电炉无论是冷态,热态,加半炉料或加满料时,半桥串联逆变器都能够输出额定功率,功率因数恒定为0.98。具有熔化速度快,能耗低,运行稳定可靠等特点。设备由一套串联谐振中频电源和两台无芯钢壳感应熔化电炉以及系统正常运行所需的辅助设备组成。

       一台串联谐振双输出电源带二只电炉可同时工作(俗称2台同时熔化炉),即输出功率可以在两个炉体之间无级任意分配,可以同时对两个炉体进行送电, 一个保温, 一个熔炼。

    12脉整流逆变串联5T/3500kw熔化炉主要技术指标

    熔化炉工作模式:

    1.1 一套炉体熔炼生产,另一套炉体备用。功率设置为3500kw,熔化时间(5T铁水至1550℃)≤55分钟/炉

    1.2 一套炉体熔炼,一台炉体保温(精炼),熔炼功率为3200kw保温功率≤300KW/个炉。在这种状态下,熔化时间(5T铁水至1550℃)≤60分钟。

    1.3 两台炉体同时熔炼生产。

    A、综合指标

    序号

    项目

    指标要求

       1

    设备形式

    中频熔炼炉

    2

    设备用途

    用于熔炼碳钢、铸铁、铝

    3

    额定容量

    5T

    4

    最大容量

    5T+10%

    5

    工作温度

    1550

    6

    冶炼材质

    铸钢、铸铁

    7

    下出料方式

    液压:液压控制

    9

    工作噪声

    <85分贝

    10

    炉体结构

    钢壳

    12

    熔化率

    5T/h

    13

    出炉温度

    1550±20℃

    14

    熔化电耗

    550±5% kW.h/t铸钢

    500±5% kW.h/t铸铁

    15

    熔化时间

    55分钟/炉

    B、电气指标:

    序号

    项目

    指标

    1

    电源功率

    3500kw / 6125T

    2

    整流项数

    12

    3

    逆变器

    SCR串联逆变

    4

    额定频率              

    250Hz

    5

    进线电压

    660V

    6    

    中频电压  

    4500V-4800V

    7

    启动成功率     

    100%

    8

    功率因数

    0.98

    C、配冷却系统参数

    序号

    项目

    指标

    1

    闭环冷却塔

    ZXZ-N320T一体分层塔两套70T和250T一体分层

    2

    冷却塔壳体

    镀铝锌板 或304不锈钢板

    3

    风机配套电机

    5.5KW X 2

    4

    喷淋水泵

    4KW

    5

    循环泵

    22kw

    6

    冷却器

    304冷却器

    C、炉体指标

    序号

    项目

    指标要求

    1

    炉壳结构

    钢壳

    2

    炉壳材质

    45#钢

    3

    加厚面板

    20mm

    4

    磁轭材质

    Z11-0.23

    5

    磁轭覆盖率

    85%

    6

    磁轭夹紧

    不锈钢 1Cr18Ni9

    7

    磁轭散热方式

    双水冷

    8

    感应器铜管材质

    T2纯铜99.9

    9

    感应器铜管规格

    壁厚≥7

    10

    感应器匝数

    按设计

     

    11

    感应器绝缘

    3道浸漆,双层包扎,耐压8000V

    感应器绕制

    加长形双并绕,机器绕制(非手工绕制)

    感应器绕制

    机器绕制

    感应圈内径

    1140mm

    感应圈高度

    1550

    12

    水路

    88水路连接软管

    13

    出线方式

    14

    水冷圈材质

    紫铜管

    15

    炉壳发热量

    <75℃(炉底与炉盖除外)

    16

    绝缘

    线圈与磁轭绝缘采用云母板双层隔离

    17

    螺栓

    普通碳钢螺栓为8.8级。其他螺栓不锈钢材质

    18

    水路连接软管

    采用无阻燃高绝缘橡胶管

    19

    集水器

    不锈钢材质

    D.炉料材料

    1

    耐火胶泥

    GROUT 563A美国-天津联矿产品

    串联逆变中频电源简介:

    串联逆变中频电源采6相12脉串联逆变。串联.整流变压器所需技术参数

    型号:

    ZS11-3500KVA/10KV/660v

    额定容量:

    Se=35000kva

    一次电压:

    U1=10000V±5% 6相  12脉 50HZ

    一次电流:

    I1=202A

    二次电压:

    U2= 380V

    二次电流:

    I2=1530A X 2

    调压方式:

    档无励磁手动调压

    联结组别:

    D/d。-yn11

    阻抗电压:

    Z75o=6.5%

    效率:

    97%

     

    1, equipment type:

    This equipment is a power-saving type product, which uses a half-bridge series inverter intermediate frequency power supply (voltage resonance). When the electric furnace is cold, hot, half-filled or filled, the half-bridge series inverter can output rated power with a constant power factor of 0.98. It has the characteristics of fast melting speed, low energy consumption and stable and reliable operation. The equipment consists of a series resonant intermediate frequency power supply and two coreless steel shell induction melting furnaces and auxiliary equipment required for the normal operation of the system.

       A series resonant dual output power supply with two electric furnaces can work at the same time (commonly known as one to two), that is, the output power can be randomly distributed between the two furnace bodies, and the two furnace bodies can be simultaneously powered, one insulation , one smelt.

    2, 12-pulse rectification inverter series 5T / 3500kw melting furnace main technical indicators

    Melting furnace working mode:

    1.1 One set of furnace body is smelted and the other set is spared. Power setting is 3500kw, melting time (5T molten iron to 1550 °C) ≤ 55 minutes / furnace

    1.2 A set of furnace body melting, a furnace body insulation (refining), melting power of 3200kw insulation power ≤ 3 00KW / furnace. In this state, the melting time (5 T iron water to 1 5 5 0 ℃) ≤ 60 minutes.

    1.3 The two furnace bodies are simultaneously smelted and produced.

    A, comprehensive indicators

    Serial number

    project

    Indicator requirements

       1

    Equipment form

    Medium frequency melting furnace

    2

    Equipment use

    Used for melting carbon steel, cast iron, aluminum, etc.

    3

    Rated Capacity

    5T

    4

    Maximum capacity

    5T + 1 0%

    5

    Operating temperature

    15 5 0 °C

    6

    Smelting material

    Cast steel, cast iron

    7

    Lower discharge mode

    Hydraulic : hydraulic control

    9

    Working noise

    <85 decibels

    10

    Furnace structure

    Steel shell

    12

    Melting rate

    5T /h

    13

    Release temperature

    1 5 5 0 °C ±20 °C

    14

    Melting power consumption

     55 0±5% kW.h/t cast steel

     5 0 0±5% kW.h/t cast iron

    15

    Melting time

    55 minutes / furnace

    B. Electrical indicators :

    Serial number

    project

    index

    1

    Power supply

    3500kw / 6 phase 12 pulse 5T

    2

    Number of rectifiers

    12 veins

    3

    Inverter

    SCR series inverter

    4

    Rated frequency

    250 Hz

    5

    Line voltage

    660 V

    6

    IF voltage

    45 00V -4800V

    7

    Start success rate

    100%

    8

    Power factor

    0.9 8

    C, with cooling system parameters

    Serial number

    project

    index

    1

    Closed loop cooling tower

    ZXZ-N 320 T integrated layering tower two sets of 70T and 250T integrated layering

    2

    Cooling tower housing

    Galvanized or 304 stainless steel

    3

    Fan supporting motor

    5.5 KW X 2

    4

    Spray pump

    4 KW

    5

    Main circulation pump

    22kw

    6

    Cooler

    304 cooler

    C, furnace index

    Serial number

    project

    Indicator requirements

    1

    Furnace shell structure

    Steel shell

    2

    Furnace shell material

    45 # steel

    3

    Thickened panel

    20mm

    4

    Yoke material

    Z11-0. 23

    5

    Yoke coverage

    8 5%

    6

    Yoke clamping

    Stainless steel 1Cr18Ni9

    7

    Yoke cooling method

    Double water cooling

    8

    Sensor copper tube material

    T2 pure copper 99.9

    9

    Inductor copper tube specifications

    Wall thickness ≥ 7

    10

    Sensor turns

    By design

     

    11

    Inductor insulation

    3-way dipping paint, double-layer dressing, pressure resistance 8000V

    Sensor winding

    Long and double winding, machine winding (not hand-wound)

    Sensor winding

    Machine winding

    Induction ring inner diameter

    1140mm

    Induction loop height

    1550

    12

    waterway

    8 in 8 out , water connection hose

    13

    Way out

    Come out

    14

    Water cooling ring material

    Copper tube

    15

    Furnace shell heat

    <75 ° C (except the furnace bottom and the furnace cover)

    1 6

    insulation

    The coil and the yoke are insulated by a double layer of mica board.

    17

    bolt

    Ordinary carbon steel bolts are grade 8.8. Other bolts stainless steel

    18

    Water connection hose

    Use non-flame retardant high insulation rubber tube

    19

    Water collector

    Stainless steel

    D. Furnace material

    1

    Refractory clay

    GROUT 563A US-Tianjin Union Products

    3 , series inverter IF power supply introduction:

    Adopt series inverter frequency power supply 6 with pulse series inverter 12. Series III . Technical parameters required for rectifier transformer

    model:

    ZS11- 3500 KVA/10KV / 660v

    Rated Capacity:

    Se= 35000 kva

    Primary voltage:

    U1=10000V±5% 6- phase 12-pulse 50HZ

    Primary current:

    I1= 202 A

    Secondary voltage:

    U2= 380V

    Secondary current:

    I2= 1530A X 2

    Pressure regulation method:

    Three-speed manual non-excitation regulator

    Connection group:

    D/d. -yn11

    Impedance voltage:

    Z75o=6.5%

    effectiveness:

     97%

     

     

     

     

     

     

     

    七、熔化炉旋风式吸尘罩简要说明

     

     

      

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

    http://www.firstfurnace.com/BdwlkjProduct.asp?id=445

    http://www.firstfurnace.com/BdwlkjProduct.asp?id=459

    http://www.yxdianlu.com/BdwlkjProduct.asp?id=440


    Copyright© 2007-2013洛阳松导感应加热科技有限公司 All Rights Reserved 
    手 机:15038554363
    本站关键词:中频炉、中频电炉、熔炼炉