设为首页 设为收藏

联系方式

 

洛阳松导感应加热科技有限公司 

联系方式:15038554363  

24小时技术热线:15038554363

邮 箱:1390003299@qq.com

厂址:河南省洛阳市洛新工业园区

  • 产品
  • 梯形铝锭在线提温设备

    0.2T中频定点浇注炉

    钢坯加热炉

    超高温烧结炉

    钢管在线加热及保温装置

    40KW感应加热取暖炉

    氮化硼专用中频加热线圈

    电机端环焊接设备

    电机转子导条焊机设备

    5吨中频炉熔化铸铁

    底出水熔铝炉

    侧下出水中频炉

    0.2吨铜雾化定点浇注炉

    3吨中频炉熔化铸钢件

    3吨中频炉熔化废铝

    3吨中频炉2500kw熔化铸铁

    1吨中频炉熔化铸铁件专用炉

    1吨12脉一拖二中频炉

    2吨中频炉用熔化铸钢件

    铸铁件1吨中频炉

    2吨铸造中频炉

    铸造1吨中频炉

    1.5吨钢壳液压中频炉

    1.5吨钢壳液压定点浇注炉

    3吨串联逆变中频炉

    圆钢感应加热炉

    铝棒感应加热炉

    方钢感应加热炉

    电炉文章
    分享到:
        本文为技术资料或者文章来自网络,仅供参考学习,如涉嫌侵权,请告知删除
        

    一、项目内容:

       Ф108—Ф1016钢管单层环氧粉末喷涂防腐生产线

    二、设计依据:

    钢管直径:Ф108—Ф1016

            钢管长度:8000㎜-12000㎜

    工艺速度:1200㎜/min—5000㎜/min

    三、管道传送架

    根据用户要求,我公司环氧粉末喷涂Ф108—Ф1016钢管防腐生产线设计为以单轮为动力单元的传送线,这样使管道运行速度更加平稳并方便了大小管螺距的调整。减速机采用WPA型,动力为7.5KW变频电机,一共6台。动力控制采用集中控制,控制柜为琴式柜,变频器集中在四个控制柜中,变频器采用国内知名品牌。传送架底座采用国标20#槽钢、20#矩形钢和 14㎜厚钢板焊接。此生产线传送架的规格为2000㎜×6000㎜×13个(每个架装4组轮胎)。2000㎜×800㎜×10个,(其中八架一组轮胎,一组装高温轮,另有两单架每架装二组轮胎)。传送轮为600-9充气轮胎(比实心轮变形能力强,管道运行平稳)。传动轮底座用4个螺钉固定在孔间距一致的调节轨道上,方便大小管间距的调节;角度调节采用丝杠调节,提高了管道传送精度并减少了劳动强度。总长度为 90米。            

    四、除锈机:

    本机是在引进美国、意大利的先进技术的基础上,采用现代计算机模拟技术,研制开发的一种新型钢管外壁抛丸清理设备,可去除钢管表面的锈和氧化皮,完全达到钢管外壁涂履前的清理要求,可满足大、中型工程钢管外壁清理需要。它具有以下优点:

    1、采用大抛丸量、高抛射速度的国际上第五代悬臂离心式抛丸器,显著地提高了清理效率,获得满意的清理质量,属专利产品。

    2、该设备是根据国内外先进技术重新设计而研制成功的,具有生产率高、操作方便、体积小的特点,属国内首创。

    五、中频加热:

    此生产线配置500KW和1000KW共二台中频加热设备。500KW用于除锈机前,除去钢管表面水分,提高除锈效果,预防钢丸结块。1500KW用于外环氧粉末喷涂加热。

    500kw参数:

    名    称

    参  数

    名   称

    参    数

    输入电压

    380V

    输出最高电压

    780V

    输入电流

    820A

    输出最大电流

    1000A

    输入频率

    50HZ

    输 出 频 率

    500HZ~800HZ

    1000kw参数:

    名    称

    参  数

    名   称

    参    数

    输入电压

    380V

    输出最高电压

    780V

    输入电流

    1700A

    输出最大电流

    2000A

    输入频率

    50HZ

    输 出 频 率

    500HZ~800HZ

     

    六、喷粉系统:

    1、8枪控制中心。       DK型        2                                

    以上装置每套含自动喷枪8支,喷枪为内置高压,控制柜控制8支自动喷枪的电压、电流及气路系统。并控制8支文丘里供粉泵供粉系统。

    以上装置每套含流化床供粉系统1套,流化床外形尺寸:(L×W×H)800×775×570(mm)含8支文丘里供粉泵。

    七、水冷却室:

      水冷却室采用塑钢玻璃窗封闭,美观大方,便于观察。每面做有几个活动窗,方便进入。冷却水水泵采用流量为每小时100立方三台(一台备用)。另外中频冷却水泵二台,流量为每小时25立方。冷却水管调节阀门装在操作柜一侧,便于调节。

     

      九、 空压机及拨管机构:

    本生产线配备一台10立方螺杆式空压机,一台10立方空气干燥机,1.5立方储气罐一台供喷粉设备用(配备3个过滤器),但气量有富余,所以把拨管系统的油缸改为气缸,节省了液压站及液压油的投资和每年换液压油的费用。维修也干净、方便。共需要8个拨叉及气缸。(输气管道及储气包由用户负责)

      十、 放管平台

           上管、下管、过渡平台均采用20#国标工字钢焊接,保证了平台的坚固性。三个平台总长30米(长度视现场情况定,由用户制作)。

      十一  制造及安装工期

      制作工期为合同生效之日起50天制作完毕,安装工期20天(安装条件具备)。

    A single layer of epoxy powder coating Ф 108 -Ф1016 pipe coating line

    1, the project content:

    Ф108 -Ф1016 steel single layer of epoxy powder coating Coating Production Line

    2, the design basis:

    Steel pipe diameter: Ф 108 —Ф1 016

            Steel pipe length: 8000mm-12000mm

    Process speed: 1200mm/min - 5 000mm/min

    3, the pipeline conveyor

    According to user requirements, our single layer of epoxy powder coating Ф 108 -Ф1 016 pipe coating line is designed as a transmission line in a single round of the power unit, so that the speed of the pipeline operation more smoothly and easily adjust the size of the pitch tube. The reducer adopts WPA type, and the power is 7.5 KW inverter motor, a total of 6 sets. The power control adopts centralized control, the control cabinet is a piano cabinet, and the frequency converter is concentrated in four control cabinets. The frequency converter adopts domestic famous brands. The base of the conveyor is welded with GB 20# channel steel, 20# rectangular steel and 14mm thick steel plate. The specification of this production line conveyor is 2000mm × 6000mm × 13 (four sets of tires per rack). 2000mm × 800mm × 10, (including eight sets of tires, one assembled high-temperature wheel, and two single-frame each set of two sets of tires). The transfer wheel is a 600-9 pneumatic tire (stronger than the solid wheel, the pipe runs smoothly). The base of the transmission wheel is fixed on the adjusting rail with the same hole spacing by 4 screws to facilitate the adjustment of the size of the pipe. The angle adjustment adopts the screw adjustment, which improves the pipeline transmission accuracy and reduces the labor intensity. The total length is 90 meters.

    4, the descaling machine:

    This machine is based on the introduction of advanced technology from the United States and Italy, using a modern computer simulation technology, developed a new type of steel pipe outer wall shot blasting equipment, which can remove the rust and scale on the surface of the steel pipe, completely before the outer wall of the steel pipe is painted. The cleaning requirements can meet the needs of cleaning the outer wall of large and medium-sized engineering steel pipes. It has the following advantages:

    1. The fifth-generation cantilever centrifugal blasting machine with large shot blasting and high throwing speed has significantly improved the cleaning efficiency and obtained satisfactory cleaning quality. It is a patented product.

    2. The equipment has been successfully developed according to the redesign of advanced technology at home and abroad. It has the characteristics of high productivity, convenient operation and small volume, and is the first in China.

    5, medium frequency heating:

    This production line is equipped with two intermediate frequency heating devices of 500KW and 1000KW. Before using 500KW for descaling machine, remove the surface moisture of the steel pipe, improve the descaling effect, and prevent the steel pellets from agglomerating. 1500KW is used for external epoxy powder coating heating.

    5 00kw parameters:

    Name

    Parameter

    Name

    Parameter

    Input voltage

    380V

    Output maximum voltage

    780V

    Input Current

    82 0A

    Output maximum current

    1 000A

    Input frequency

    50HZ

    Output frequency

    500HZ800HZ

    10 00kw parameters:

    Name

    Parameter

    Name

    Parameter

    Input voltage

    380V

    Output maximum voltage

    780V

    Input Current

    1700A

    Output maximum current

    2000A

    Input frequency

    50HZ

    Output frequency

    500HZ800HZ

     

    6, dusting system:

    1, 8 gun control center. DK type 2 sets

    Each set of the above devices contains 8 automatic spray guns, the spray gun is built-in high pressure, and the control cabinet controls the voltage, current and pneumatic system of 8 automatic spray guns. And control 8 venturi powder pump powder supply system.

    Each set of the above devices contains a fluidized bed powder supply system. The fluidized bed has the following dimensions: (L×W×H) 800×775×570 (mm) containing 8 venturi powder pumps.

    7, water cooling room:

    The water cooling room is closed by plastic steel glazing, which is beautiful and easy to observe. There are several activity windows on each side for easy access. The cooling water pump uses a flow rate of three cubic meters per hour (one standby). In addition, two intermediate frequency cooling water pumps have a flow rate of 25 cubic meters per hour. The cooling water pipe regulating valve is installed on the side of the operation cabinet for easy adjustment.

     

      8, air compressor and pipe mechanism:

    The production line is equipped with a 10-cube screw air compressor, a 10-cubic air dryer, and a 1.5-cubic gas storage tank for powder spraying equipment (with 3 filters), but the gas volume is surplus, so the pipe is put The system's cylinders were changed to cylinders, saving investment in hydraulic stations and hydraulic oil and the cost of changing hydraulic oil every year. Maintenance is also clean and convenient. A total of 8 forks and cylinders are required. (The gas pipeline and gas storage bag are the responsibility of the user)

     9. Pipeline platform

    The upper tube, the lower tube and the transition platform are all welded with 20# national standard I-beam, which ensures the robustness of the platform. The total length of the three platforms is 30 meters (the length is determined by the site and made by the user).

      10, manufacture and installation period

    The production period is 50 days from the effective date of the contract, and the installation period is 20 days (the installation conditions are available).

     http://www.firstfurnace.com/BdwlkjProduct.asp?id=397


    Copyright© 2007-2013洛阳松导感应加热科技有限公司 All Rights Reserved 
    手 机:15038554363
    本站关键词:中频炉、中频电炉、熔炼炉