设为首页 设为收藏

联系方式

 

洛阳松导感应加热科技有限公司 

联系方式:15038554363  

24小时技术热线:15038554363

邮 箱:1390003299@qq.com

厂址:河南省洛阳市洛新工业园区

  • 产品
  • 梯形铝锭在线提温设备

    0.2T中频定点浇注炉

    钢坯加热炉

    超高温烧结炉

    钢管在线加热及保温装置

    40KW感应加热取暖炉

    氮化硼专用中频加热线圈

    电机端环焊接设备

    电机转子导条焊机设备

    5吨中频炉熔化铸铁

    底出水熔铝炉

    侧下出水中频炉

    0.2吨铜雾化定点浇注炉

    3吨中频炉熔化铸钢件

    3吨中频炉熔化废铝

    3吨中频炉2500kw熔化铸铁

    1吨中频炉熔化铸铁件专用炉

    1吨12脉一拖二中频炉

    2吨中频炉用熔化铸钢件

    铸铁件1吨中频炉

    2吨铸造中频炉

    铸造1吨中频炉

    1.5吨钢壳液压中频炉

    1.5吨钢壳液压定点浇注炉

    3吨串联逆变中频炉

    圆钢感应加热炉

    铝棒感应加热炉

    方钢感应加热炉

    技术资料
    分享到:
        本文为技术资料或者文章来自网络,仅供参考学习,如涉嫌侵权,请告知删除
        

    中频炉的使用方法

    1、 熔化途中发现感应器匝间炉衬发红或有其他穿钢迹象,要及时停炉把钢水倒出,不要存有侥幸心理。

    每炉出钢后,要检查炉衬炉壁,如发现有局部相对“发黑”,要果断停炉,防止下漏钢水

    2中频炉加料时,严禁加入有密封、半密封的物体(容器),管状的物体,潮湿、油污、带水、带冰(要先摆在炉口烘干后再加入)、严重锈蚀、过冷的物体,或其它易爆炸物。曾经有材料中夹带雷管加入炉中,炸瞎炉工的一只眼睛。

    装填炉料时,不准用锤子猛打,应轻放、轻敲以免损坏炉膛。

    不锈钢回炉料不少是化工厂拆卸下来的不锈钢容器、管道,吸附不少的化学材料,最好在下炉之前把化学材料处理干净,免得污染空气。

    炼合金钢加入合金材料时,应在预热后用钳子夹住,缓慢,分批加入,加入时操作者脸部应避开炉口。

    How to use induction melting furnace

    1. During the melting process, if the inter-turn furnace lining of the inductor is red or there are other signs of steel wear, stop the furnace in time to pour out the molten steel, and don't be lucky.

    After each furnace is tapped, check the furnace lining and furnace wall. If there is a relatively "black" part, stop the furnace decisively to prevent molten steel from leaking.

    2. When feeding the induction melting furnace, it is strictly forbidden to add sealed, semi-sealed objects (containers), tubular objects, damp, oily, water, or ice (it must be placed in the furnace mouth and dried before adding), or severely corroded , Objects that are too cold, or other explosives. Once there was a detonator entrained in the material and added to the furnace, blowing up one eye of the furnace worker.

    When loading the furnace material, do not hit it with a hammer, and should be gently placed and tapped to avoid damage to the furnace.

    Many of the stainless steel reheating materials are stainless steel containers and pipes dismantled by chemical plants, which absorb a lot of chemical materials. It is best to clean up the chemical materials before going out of the furnace to avoid polluting the air.

    When adding alloy materials to alloy steel, it should be clamped with pliers after preheating, and added slowly and in batches. When adding, the face of the operator should avoid the furnace mouth


    Copyright© 2007-2013洛阳松导感应加热科技有限公司 All Rights Reserved 
    手 机:15038554363
    本站关键词:中频炉、中频电炉、熔炼炉