标题：中频熔铜炉—中频熔铜炉，熔少量铜的设备，化铜炉厂家，熔铜成本最低，快速熔铜炉制造商

关键词：中频熔铜炉

描述：中频熔铜炉技术选型，中频熔铜炉配置，熔铜是否可以使用中频感应炉？中频熔铜炉使用操作步骤

中频熔铜炉

中频熔铜炉，熔少量铜的设备，化铜炉厂家，熔铜成本最低，快速熔铜炉，
用途：最适合熔化铜粉，铜丝，铜屑，铜块，铜皮，电解铜的炉子和设备，熔化铜板，熔化铜棒，熔化铜带，熔化铜管，熔化铜线，熔化铜箔的设备，

一，中频熔铜炉设备选型表

二，中频熔铜炉配置：

三，客户自配装机附件（循环冷却系统）： 

1 . 三相空气开关   400A 1个 ； 

2 . 电源连接软电缆线  90mm² 数米 ； 

3 . 冷却塔30吨  1个 ;

4 . 水泵 3.0kw/扬程30-50米 1台;

5、设备进出水水管：高压增强水管外直径16毫米，内直径12毫米若干米

6、水泵进出水水管：1寸（内径25毫米）内有钢丝高压增强管若干米

四，中频熔铜炉使用操作步骤： 

1、接电：电源线分别接入专用的三相空气开关。再接好地线。（注意三相电电力要能满足该设备使用，电线粗细要按说明书规定使用）

2、接水：（视连续工作时间和工作量）选择冷却水系统，实现水流循环冷却。

3、通水：打开水路，并检查设备每路出水看是否有水流出，流水量及压力是否正常。

4、通电：先打开控制电源开关，再接打开机器后面的空气开关，然后再打开控制板上的电源开关。  

5、启动：第一炉启动前应将加热功率电位器尽量调至最小，待启动后再缓温调至所需的功率。按下启动按键启动机器，此时面板上加热指示灯亮，同时会有正常工作的提示声和工作灯的同步闪烁。
6. 观察和测温：在加热过程中主要是用目测的方式根据经验确定何时停止加热。

7. 关机：关机时，要先关设备控制开关，再关外部总电源开关，然后推迟1小时左右待炉内温度降下来后；再关设备冷却水，以利机器内部的热量和感应圈的热量散发。
8、冬天在容易结冻的地区，要注意，每次使用结束后，要用压缩空气把设备内的进出水吹干净，以防止设备内部有水冻裂内部配件及水管。

五，客户熔铜现场图片：

六，熔铜是否可以使用中频感应炉？

熔铜炉可以选择中频熔铜炉，小型节能熔铜的有150KG~~500KG 容量的质量好熔化。

如果选择使用钢壳节能型熔铜炉，节能率又提高10%左右。性价比很高，优势很明显。

熔铜，熔锌，熔铝，都适用 中频感应炉，熔化铜及铜合金用中频炉。

Title: Medium frequency copper melting furnace - medium frequency copper melting furnace, equipment for melting a small amount of copper, copper furnace manufacturer, the lowest cost of molten copper, fast melting copper furnace manufacturer

Keywords: medium frequency copper melting furnace

Description: Medium frequency copper melting furnace technology selection , medium frequency copper melting furnace configuration, can the molten copper use medium frequency induction furnace? The operation steps of the intermediate frequency copper melting furnace:

Medium frequency copper melting furnace

Medium frequency copper melting furnace , equipment for melting a small amount of copper, copper furnace manufacturer, the lowest cost of molten copper, fast melting copper furnace, 
Uses: The most suitable melting copper powder, copper wire, copper scrap, copper block, copper, and electrolytic copper furnace equipment, copper is melted, the molten copper, the molten copper strip, the molten brass, the molten copper, the molten copper foil device,

First, the medium frequency copper melting furnace equipment selection table

Second, the medium frequency copper melting furnace configuration:

Third, the customer self- installed machine accessories ( circulation cooling system ) :

1. Three-phase air switch 400A 1 ;

2. Power connection soft cable 90 mm2 several meters;

3 . Cooling tower 30 tons 1;

4. Pump 3.0kw/ head 30-50 meters 1 set ;

5 , equipment inlet and outlet water pipes: high pressure enhanced water pipe outer diameter 16 mm, inner diameter 12 mm several meters

6. Water pump inlet and outlet water pipe: 1 inch (inner diameter 25 mm) with wire high pressure reinforced pipe several meters

Fourth, the intermediate melting Tonglu using Procedure:

1, electrical connection: access to a dedicated power supply line, respectively, three-phase air switch. Then connect the ground wire. ( Note that the three-phase electric power should be able to meet the use of the equipment, and the wire thickness should be used according to the instructions )

2 , water: (depending on continuous working time and workload) select the cooling water system to achieve water circulation cooling.

3 , water: open the waterway, and check the water outlet of each device to see if there is water outflow, whether the flow and pressure are normal .

4, power: the power switch to open the control, followed by a switch to open the air behind the machine, and then turn the power switch on the control panel.  

5 , start: Before the first furnace starts, the heating power potentiometer should be adjusted to the minimum as much as possible, and then slowly adjusted to the required power after starting. Press the start button to start the machine. At this time, the heating indicator on the panel lights up, and the prompt sound of normal operation and the work light flash simultaneously. 
6. Observation and temperature measurement: In the heating process, it is mainly determined by visual inspection when to stop heating.

7. Shutdown: Shutdown, the control device switches off first, then turn off the main power external switch, then delayed until about 1 hour after the furnace temperature down; then off equipment cooling water, the heat inside the machine to facilitate the induction loop and the heat distributing . 
8. In areas where it is easy to freeze in winter , it should be noted that after each use, compressed air should be used to blow out the water in and out of the equipment to prevent internal cracking of internal fittings and water pipes.

Five, customer molten copper scene pictures:

6. Can the molten copper use an intermediate frequency induction furnace?

The copper melting furnace can choose medium-frequency copper melting furnace, and the small energy-saving molten copper has a good quality melting of 150KG~~500KG capacity.

If you choose to use a steel shell energy-saving copper melting furnace, the energy saving rate will increase by about 10% . The price is very high and the advantages are obvious.

Fused copper, molten zinc, and molten aluminum are suitable for medium frequency induction furnaces, intermediate frequency furnaces for melting copper and copper alloys .