设为首页 设为收藏

联系方式

 

洛阳松导感应加热科技有限公司 

联系方式:15038554363  

24小时技术热线:15038554363

邮 箱:1390003299@qq.com

厂址:河南省洛阳市洛新工业园区

  • 产品
  • 梯形铝锭在线提温设备

    0.2T中频定点浇注炉

    钢坯加热炉

    超高温烧结炉

    钢管在线加热及保温装置

    40KW感应加热取暖炉

    氮化硼专用中频加热线圈

    电机端环焊接设备

    电机转子导条焊机设备

    5吨中频炉熔化铸铁

    底出水熔铝炉

    侧下出水中频炉

    0.2吨铜雾化定点浇注炉

    3吨中频炉熔化铸钢件

    3吨中频炉熔化废铝

    3吨中频炉2500kw熔化铸铁

    1吨中频炉熔化铸铁件专用炉

    1吨12脉一拖二中频炉

    2吨中频炉用熔化铸钢件

    铸铁件1吨中频炉

    2吨铸造中频炉

    铸造1吨中频炉

    1.5吨钢壳液压中频炉

    1.5吨钢壳液压定点浇注炉

    3吨串联逆变中频炉

    圆钢感应加热炉

    铝棒感应加热炉

    方钢感应加热炉

    电炉文章
    分享到:
        本文为技术资料或者文章来自网络,仅供参考学习,如涉嫌侵权,请告知删除
        

    一、项目内容:

    Ф219—Ф1219钢质弯头双层环氧粉末喷涂防腐生产线

    二、设计依据:

     弯头直径:     Ф219—Ф1219

         曲率半径:      4~6D

    工艺速度:      300㎜/min—1000㎜/min

        三、输送辊道

      根据工艺要求,我公司Ф219—Ф1219弯头双层环氧粉末喷涂防腐生产线设计为,以单辊挂胶轮为动力单元的输送辊道,这种方式可以不用底部环轨,输送辊道呈扇形排列。各滚道的间距及与输送方向的角度均可调整,用户在使用过程中根据管径的大小可以任意安装和改变输送辊道的直径来适应弯头。辊轮外壁包裹有橡胶,使工件行走平稳,不伤害环氧粉末涂层。

        本输送辊道可通过变频器实现无级调速。各滚道的动力通过轴装减速机产生,可根据动力需要来布置不同数量的减速机。滚道运转平稳、噪音低等优点。

    四、除锈机:

      本机专用于钢管弯头外壁的抛丸清理,以去除其表面的氧化皮并增加表面积,增大涂敷粘着力。

    五、中频电源加热:

    此生产线配置1000KW中频加热设备。此设备控制部分采用专门设计的控制线路,具有过压、过流、 限压/限流、缺相、欠压、欠水压等保护。

      控制线路专设集成箱与高压区全隔离,保持控制室清洁,大大提高控制线路板寿命和系统可靠性。优选国内知名厂家大功率变流器件。电器元件采用德力西品牌。

    因此具有100%的设计安全系数,增加整个系统可靠性。采用宽大的空气冷却铜排,与水冷铜排相比,更多的能量用于加热,效率增加,不需要维修。

    电源起动采用零电压起动,无冲击,在空载、重载等状态时均能可靠起动, 稳定可靠,无故障时间长,方便检修。

    配备一套纯净水冷却交换装置,冷却效果好,使各管路不 容易 发生堵塞,降低了中频电源的故障率,提高设备的使用寿命。

      1000kw参数:

    名    称

    参  数

    名   称

    参    数

    输入电压

    380V

    输出最高电压

    780V

    输入电流

    1700A

    输出最大电流

    2000A

    输入频率

    50HZ

    输 出 频 率

    500HZ~800HZ

     

    六、喷粉系统:

     1、8枪控制中心       DK型             4                                

    以上装置每套含自动喷枪8支,喷枪为内置高压,控制柜控制8支自动喷枪的电压、电流及气路系统。并控制8支文丘里供粉泵供粉系统。

    以上装置每套含流化床供粉系统1套,流化床外形尺寸:(L×W×H)800×775×570(mm)含8支文丘里供粉泵。

     

    空压机及水喷淋系统

    本生产线配备一台6立方螺杆式空压机,一台6立方空气干燥机,1.0立方储气罐一台供喷粉设备用(配备3个过滤器)。水喷淋系统采用开放式,方便辊道的调整。

    附设备明细及价格表:

     

     

    Ф219—Ф 1 2 19 Steel elbow double-layer epoxy powder coating anti-corrosion production line

    Epoxy powder coating anti-corrosion production line

     

    1, the project content:

    Ф219—Ф 1 2 19 Steel elbow double-layer epoxy powder coating anti-corrosion production line

    2, the design basis:

    Elbow diameter:      Ф219—Ф 1219

    Radius of curvature :       4~6D

    Process speed: 3 00mm/min - 10 00mm/min

    3, the conveyor roller

    The process according to claim I Ф219-Ф 1219 double elbow anticorrosive epoxy powder coating production line is designed to roll a single tire to hang the power unit conveying roller, this embodiment can not track the base ring, as a conveyor roller Fan-shaped arrangement. Each track pitch and the angle of the conveying direction can be adjusted, the user during use to accommodate the size of the diameter of the elbow according to install and can be arbitrarily varying the diameter of the roller conveyor. The outer wall of the roller is covered with rubber to make the workpiece travel smoothly without damaging the epoxy powder coating.

        The conveyor roller can realize stepless speed regulation through the frequency converter. The power of each raceway is generated by a shaft-mounted reducer, and different numbers of reducers can be arranged according to the power demand. The raceway runs smoothly and has low noise.

    4, the descaling machine:

      This machine is specially designed for shot blasting of the outer wall of the steel pipe elbow to remove the scale on the surface and increase the surface area, increasing the adhesion of the coating.

    5, medium frequency power supply heating:

    This production line is equipped with a 10 00 KW intermediate frequency heating device. This equipment control part uses specially designed control lines with overvoltage, overcurrent, Pressure limiting / current limiting, phase loss, under voltage, under water pressure and other protection.

      The control line dedicated integrated box is completely isolated from the high pressure area, keeping the control room clean , greatly improving the life of the control circuit board and system reliability. It is preferred to have high-power converter devices from well-known domestic manufacturers. The electrical components are based on the Delixi brand.

    Therefore, it has a design safety factor of 100%, which increases the reliability of the entire system. With a large air-cooled copper row, more energy is used for heating than the water-cooled copper row, which increases efficiency and requires no maintenance.

    The power supply starts with zero voltage and has no impact. It can be reliably started in the state of no-load, heavy load, etc. It is stable and reliable, has no long fault time and is convenient for maintenance.

    Equipped with a set of pure water cooling exchange device, the cooling effect is good, so that the pipelines are not easily Blockage occurs, reducing the failure rate of the intermediate frequency power supply and improving the service life of the equipment.

    10 00kw parameters:

    Name

    Parameter

    Name

    Parameter

    Input voltage

    380V

    Output maximum voltage

    780V

    Input Current

    1700A

    Output maximum current

    2000A

    Input frequency

    50HZ

    Output frequency

    500HZ~800HZ

     

    6, dusting system:

    8 gun control center DK type 4 sets:Each apparatus having the above automatic gun 8, a high-pressure spray gun is built, control cabinet 8 controls automatic spray gun voltage, current and gas system. And control 8 venturi powder pump powder supply system.

    Each set of the above devices contains a fluidized bed powder supply system. The fluidized bed has the following dimensions: (L×W×H) 800×775×570 (mm) containing 8 venturi powder pumps.

     

    7, air compressor and water sprinkler system :

    The production line is equipped with a 6- cubic screw air compressor, a 6- cubic air dryer, and a 1.0- cubic gas storage tank for powder spraying equipment (with 3 filters) . The water sprinkler system is open and easy to adjust the roller table.

    Attached equipment details and price list:


    Copyright© 2007-2013洛阳松导感应加热科技有限公司 All Rights Reserved 
    手 机:15038554363
    本站关键词:中频炉、中频电炉、熔炼炉